• p. 17:  in Example 2.3, in the second equation, “V_R” should be “R”
• p. 47:  in Question 2.2, remove the last sentence
• p. 50:  in Question 2.16, change “the voltages” to “the steady state voltages”
• p. 69:  in Class Discussion Item 3.7, reverse the polarity on voltage source V_L
• p. 71:  in Figure 3.14, replace “n p n” with “p n p”
• p. 77:  in Figure 3.19, the pin order should be “B C E” (not “C B E”) for the TO-220 package
• p. 81:  in Figure 3.23, the switch should be in the top-left portion of the MOSFET circuit and there should a resistor connected between the gate and source
• p. 83:  in the 1st paragraph of Section 3.5.2, in the 3rd line, “V_DS” should be “V_GS“
• p. 86:  in question 3.1, the vertical axis limits should be 10 and -10, not 1 and -1
• p. 106:  Example 4.2 should be a Class Discussion Item
• pp. 113-114:  the 1st sentence under Equation 4.60 should be switched with the 1st sentence under Equation 4.62
• p. 118:  in Equation 4.73, the bracketed term should be squared
• p. 122:  in the equation for x(t, w), replace “X₀[(w)” with “X₀(w)[“
• p. 130:  in Figure 4.24, the flow through C₁ should be (I₃ – I₂) instead of (I₁ – I₂)
• p. 131:  in Class Discussion Item 4.10, add ” made.” to the end of the last sentence
• p. 143:  in Figure 5.8, replace “R_B” with “R_F“
• p. 156:  in Figure 5.22, V_ref and V_in should be swapped
• p. 165:  in the paragraph between the figures, in the first sentence, replace “common to both” with “difference between the two”, and in the 2nd sentence, delete the word “not”
• p. 166:  in the 2nd figure, the node on the right should be labeled “C”
• p. 200:  in Example 6.4, in the last sentence, “during a high level” should be “at positive edges”
• p. 206:  Example 6.5 should be a Class Discussion Item instead
• p. 206:  in Figure 6.26, connect the complementary output (Q bar) of each flip-flop to the K input of the adjacent flip-flop, and replace “S_i” with “S_o“
• p. 214:  in the figure, replace “7404” with “7414” and add an inversion circle to the Schmitt trigger
• p. 229:  in problem 6.16, add positive-edge-triggered symbols to the flip-flops
• p. 235:  in Example 7.1, the maximum frequency component in the signal is “a” (1 Hz), not “(a+b)/2” (0.95 Hz); so, in the paragraph before the figure, replace “1.9 Hz” with “2 Hz”
• p. 242:  in the 2nd sentence of the 2nd paragraph, the list should start with “1/2” (not “1”), and “1/n” should be “1/2ⁿ“
• pp. 264, 267, and 273:  “Appendix 2” should be “Appendix 3”
• p. 278:  in Equation 8.37, in the numerator of the first term, the middle term should be ε_b
• p. 307:  below Equation 9.1, add “(per unit length of conductor)” after “the force vector”
• p. 311:  in the 7th line of the last paragraph, “clockwise” should be “counterclockwise”
• p. 313:  in Figure 9.7, the torque arrow should point counterclockwise, not clockwise
• p. 319:  in Figure 9.15, the polarity of V_emf should be in the opposite direction
• p. 327:  in Figure 9.20, in the 3rd and 4th drawings at the bottom, the rotor should be turned 90 degrees.
• p. 385:  in the “Centrifugal Force” bullet, “inward” should be “outward”

If you find any additional errors, please report them to David.Alciatore@colostate.edu so they can be posted for the benefit of others.  Thanks!